|
|
| 啊啾哇MP118TH-C其它 |
 |
产品简介
额定电流: 1A-5A 品牌: AUQAV
型号: MP118TH-C 产品型号: MP118TH-C
产品报价：130元 |
|
| 啊啾哇MP118TH-C其它详细介绍 |
1. Power Supply Overview 电性能指标:
1.1 Table 1 Input Electrical Characteristics Overview（输入特性）
| Input voltage range 输入电压 |
90Vac to 264Vac |
| Normal voltage range 标称输入 |
100Vac to 240Vac |
| Frequency range 频率范围 |
50Hz/60Hz±5% |
Max input ac current
满载输入电流 |
2.6Amax at full load and 90Vac condition |
Inrush current (cold start)
浪涌电流 |
50Atyp peak, 120Vac; 100Atyp peak, 220Vac |
| Efficiency(full load) 效率 |
82%min at 90Vac; 86%min at 220Vac Typ. |
| Harmonic current 谐波电流 |
Meet GB17625.1-2003/IEC61000-3-2 class D |
| Leakage Current 泄漏电流 |
Less Than 0.5mA at 240Vac input |
| Standby Power Loss 待机功耗 |
≦0.5W 240Vac input at 5Vsb Output current≤10mA |
| Input Fuse 输入保险 |
T5AH/250Vac |
1.2 Output Electrical Characteristics Overview（输出特性）
1.2.1 Table 2 Output Voltage ,Current & Regulation.（输出调整率）
Output Voltage
输出电压 |
Regulation
调整率 |
Min. current
最小电流 |
Load current range
带载电流范围 |
Peak current or power
峰值电流或功率 |
| +V1(+24V) |
+V1±5% |
0.2 A |
0.2A-5A |
≤190W |
| +V2(+12V) |
+V2±5% |
0.3 A |
0.3A-3.5A |
| +5.0V |
+5.2V±2% |
0.1 A |
0.1A-1.5A |
≤15W |
| +5.0V(SB) |
+5.2V±2% |
0.01 A |
0.01A-1A |
Note:* The peak current or power should be test at other of dc output at Rated
load ,And the peak current pulse width within 100ms 峰值电流或功率的测试是在其它额定
负载时测试，且脉宽小于100 毫秒。
1.2.2 Table 3 DC Output Ripple & Noise. （输出纹波和噪声）
| Output Voltage |
Ripple & Noise (Max.) |
| +V1(+24V) |
240mVp-p@25℃; 350mVp-p@-10℃ |
| +V2(+12V) |
120mVp-p@25℃; 200mVp-p@-10℃ |
| +5.0V |
50mVp-p@25℃; 150mVp-p@-10℃; |
| +5.0V(SB) |
60mVp-p@25℃; 200mVp-p@-10℃; 150mVpp when STB |
Note: 1) Measurements shall be made with an oscilloscope with 20MHz bandwidth.
示波器须设置在20 兆赫兹带宽
2) Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a
10uF electrolytic capacitor to simulate system loading.
输出须并联0.1uF 的陶瓷电容和10uF 的电解电容来模拟负载.
1.2.3 Output Transient Response. （输出动态响应）
Table 4. Test condition.测试条件
| Voltage Tolerance Limit |
Slew Rate |
Load Change |
5.0V/5.0VS±5%
24V/12V/±10% |
0.2A/u S |
Min. to 50% load and 50% to Max load |
| All output±10% |
0.2A/u S |
Min. load to Max load | Note: Transient response measurements shall be made with a load changing repetition
rate of 50Hz to 10kHz. 以50~10KHz 的频率跳变负载来测试。
1.2.4 Table 5 DC Output Hold-Up Time. （输出保持时间）
| Output Voltage |
120Vac input |
220Vac input |
| +V1(+24V) |
≥10 m S |
≥10 m S |
| +V2(+12V) |
≥10 m S |
≥10 m S |
| +5.0V |
≥10 m S |
≥10 m S |
| +5.0V(STB) |
≥10 m S |
≥10 m S | Note: All of dc output at full load. 所有输出带满载
1.2.5 Table 6 DC Output Overshoot At Turn On & Turn Off.（输出超调）
| Output Channel |
Output(V) |
Over shoot voltage(V)超调电压 |
| Turn on 开机 |
Turn off 关机 |
| +V1(+24V) |
+ 24V |
10% |
10% |
| +V2(+12V) |
+ 12V |
10% |
10% |
| +5.0V |
+5.0V |
10% |
10% |
| +5.0V(SB) |
+5.0V |
10% |
10% | Note: All of dc output current from Min. to Max. 测试时负载范围：最小到最大
1.2.6 Table 7 DC output voltage rise time（输出上升时间）
| Output Voltage |
120Vac input &Full Load |
220Vac input &Full Load |
| +V1(+24V) |
≤100mS |
≤100mS |
| +V2(+12V) |
≤100mS |
≤100mS |
| +5.0V |
≤100mS |
≤100mS |
| +5.0V(SB) |
≤50mS |
≤50mS |
Note: The output voltages shall rise from 10% to 90% of their output voltage.
输出从10%上升到90%的时间
1.3 Remote On/Off Control：（遥控功能）
The power supply DC outputs (without +5.0Vsb) shall be enable with an active-high TTL(≥2.5V/2.0mA)-compatible signal(Ps-on). The +5.0Vsb is on whenever the AC power is present.
除5.0Vsb 外，其余输出受控于一个TTL 电平兼容的信号（Ps-on≥2.5V/2.0mA）,
5.0Vsb 上电就存在。
* When Ps-on is pulled to TTL high, the DC outputs are to be enabled.Ps-on 高电平，打开输出.
* When Ps-on is pulled to TTL low or open circuit, the DC outputs are to be disabled.Ps-on 低电平，关闭输出.
Table 8.
| Ps-on Signal |
Comments |
Outputs |
| Ps-on- high |
≥2.5V&2.0mA ( source) |
Output |
| Ps-on- low |
≤ 0.5V |
X |
| Ps-on-open |
-- |
X |
1.4 Protection: （保护功能）
1.4.1 Table 9 DC output Over Voltage Protection. （输出过压保护）
| Output Voltage |
TYP. Over Voltage |
Comments |
| +V1(+24V) |
27V |
Power supply latch into shutdown state
输出锁机 |
| +V2(+12V) |
14V |
Power supply latch into shutdown state
输出锁机 |
Note: The power supply shall be test at max AC voltage (264Vac) and min load or no load.
应该在最大交流输入电压264 伏和轻载、空载下测试。
1.4.2 Table 10 DC Output Over current Protection. （输出过流保护）
| Output Voltage |
Over Current |
Comments |
| +V1(+24V) |
≥6Atyp* |
Hiccup尝试重复启动 |
| +V2(+12V) |
≥5Atyp* |
Hiccup尝试重复启动 |
| +5V |
≥2Atyp* |
Hiccup尝试重复启动 |
| +5.0VSB |
≥1.5Atyp* |
Hiccup尝试重复启动 |
Note:* The over current protection should be test at other of dc output at Rated load but the 24V over current protection should be test at 12Vdc output at min load.5V 和5VSTB 过流保护测试是在其它额定负载时测试.而24V 过流测试是在12V 轻载电流时测试。
1.4.3 Table 11 DC Output Short Circuit Protection. （输出短路保护）
| Output Voltage |
Comments |
| +V1(+24V) |
Shutdown关机 |
| +V2(+12V) |
Shutdown 关机* |
| +5V |
Hiccup 尝试重复启动 |
| +5.0V(SB) |
Hiccup 尝试重复启动 |
Note:* The Short Circuit protection should be test at other of dc output at Rated load
短路保护测试是在其它额定负载时测试.
1.4.4 Re set After Shutdown.（保护功能复位）
Recycle the ps-on signal, the power supply will restart after the fault removed，But +5V、+5.0V(STB)output over voltage can’t be re set .
故障去除后，关掉Ps-on 信号再打开，电源即可恢复。+5V、+5.0V(STB)过压后不可恢复。
2. Isolation（绝缘性能）
2.1 Table 12 （绝缘阻抗）
| Input To Output |
DC500V 50MΩmin (at room temperature) |
| Input To FG |
DC500V 50MΩmin (at room temperature) |
| Output To FG |
Non Isolated | 2.2 Table 13 （绝缘耐压）
| Input To Output |
3000Vac 50Hz 1minute ≤10mA |
| Input To FG |
1500Vac 50Hz 1minute ≤10mA |
| Output To FG |
Non Isolated | Note: Open FG and Output return. 交流地和输出负极要断开。
3. Safety （安全规格）
The power supply shall compliance with the following Criterion:
电源安全性满足下列标准
1) UL60065
2) EN60065
3) GB8898-2001
4. EMC （电磁兼容性）
4.1 EMI （电磁干扰）
The power supply shall compliance with the following Criterion:
电源电磁干扰满足下列规则：
1) Conduction Emission : （传导干扰度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
2) Radiated Emission : （辐射干扰度）
*EN55013, CLASS B
*GB13837, CLASS B
*FCC PART15 CLASS B
4.2 EMS （电磁抗扰）
The power supply shall compliance with the following Criterion:
电源电磁抗扰满足下列规则：
1) ESD （静电抗扰度）
*GB17626.2-1998/IEC61000-4-2
2) EFT （脉冲群抗扰度）
*GB17626.4-1998/IEC61000-4-4 3KV
3) Surge （雷击浪涌）
*GB17626.5-1998/IEC61000-4-5 1.5KV / 3KV
5. Environmental Requirement （工作环境）
5.1 Temperature （环境温度）
* Operating: 0℃ to +40℃.
* Store: -20℃ to +80℃.
5.2 Humidity （环境湿度）
* Operating: from 10%to90% relative humidity (non-condensing).
* Store: from 5 to 95% relative humidity (non-condensing).
5.3 Altitude （海拔高度）
* Operating: to10,000 ft.
* Store: to 20,000ft.
5.4 Cooling Method （冷却方式）
* Ventilation cooling . 自然冷却
5.5 Vibration （振动耐受）
* 10-55Hz, 19.6m/s2(2G), 3minutes period, 60minutes each along X, Y and Z axis.
5.6 Impact （冲击耐受）
* 49m/s2(5G),11ms, once each X, Y and Z axis.
6. Dimension （物理尺寸）
* 180mm × 180mm ×11mm (长L *宽W * 高H ).板面高
7. Weight （重量）
* 约500g
8. Pin Connection (连接器脚位定义)
Table 15 Pin-CON4 Connection And Function
|
|
